|
 |
|
 블루투쓰송수신모듈 [HC06 USB] |
블루투쓰방식으로 시리얼 통신(USART)할수 있는 모듈
-> 사용이 매우 간편 합니다.
-> MASTER입니다(즉 PC의 USB포트레 연결하면 됩니다), 슬레이브와 1:1통신 가능
-> 사용전원은 DC 5V 또는 3.3V
- >연결선은 +,-,TX,RX 4가닥입니다. |
|
|
|
USB 시리얼포트를 포함하고 있어서 USB포트에 접속사용 가능 합니다.
슬레이브 모듈인 HC06과 1:1통신 가능 합니다.
Using HC06 bluetooth module, pioneering induction reset circuit, all SMT production process.
For the first time purchase with JB - MCU USB interface module users, please first installed on the computer USB virtual port driver.
note : please don't insert before you install the driver module!
Virtual port driver and USB serial debugging software provides email to download
Right please inform me in the buyer message receiving mailboxes.
The difference between host and from the machine:
Host can only with from machine matching, suitable for two devices directly via bluetooth serial port communication, such as between single-chip microcomputer and single chip microcomputer, a serial port cable and the single chip microcomputer, etc., using method and serial port;
From function and all kinds of computer with bluetooth function, bluetooth host, with most of bluetooth mobile phone, PDA, PSP, such as intelligent terminal matching, between the machine can not match.
Only one to one match between host and from the machine.
Product characteristics and directions for use:
1, the product for the USB serial port + HC06 bluetooth master-slave module combination, integrated operation turn USB serial port can be from a bluetooth module to send and receive data, support a serial port full-duplex transmission, USB2.0 data processing at full speed
2, only with HC06 module matching, pairing with computers, cell phones and so on, only when a serial port to use, can't he
3, with three module, matching indicator (green), respectively, the power indicator light (red), receive, send light TX RX (blue)
4, the bluetooth indicator light state description: slow flash: paired but temporarily not connected from module;Normally on: already and from module connection;Flash: the unpaired or pairing information has been removed, is the search link from the module
5, module Settings reset search (this circuit adopts the induction is reset, reset button)
6, in the bluetooth connection (status indicator light flashing) can turn directly via USB serial port to send when the AT command set parameters
7: the product without shell!!!!!!!!!!!!!!!!!!!!!!!!!
8: note: the higher the baud rate, sending and receiving the lower light brightness
9: green light normally on only that already matched, if the green light has been flashing, modify the baud rate, port and so on are all doesn't make any sense!!!!!!!!!!!!
Such as flashing, please check whether the matching password is consistent, bluetooth connection with port driver has nothing to do with baud rate!If not matching, modify baud rate set up doesn't make any sense to change the port number, and so on!
Module reset method:
The original HC06 using the reset button, both large and inconvenient operation, now our production of the circuit are the latest induction reset circuit.
Methods: carrying a metal (any needles, pointed tweezers, fine tip screwdriver), light touch HC06 module of 26 feet (KEY pin) backwards to open, the module of the green light from slow flash to flash, reset successful.
The AT command:
Set the parameters in the computer side, please set!
Unpaired module is in before the AT mode, matching module can't use the AT command, after this time of the bluetooth module is a serial port passthrough mode, green light is bright.
Serial data transmission (ats send the AT command mode, a serial port passthrough mode with other module sends data communications), blue lights flicker based on serial data transmission interval.
Green light normally on the bluetooth paired connection (after matching module cannot use the AT command)
Parameter Settings:
(default setting: 9600 N 1, 8 pairs password: 1234, if the default parameters without the following character set. All the configured parameter off electricity can save) :
Insert the computer directly to the USB port, correct installation after we provide driver system generates a port number, open the computer serial port debug tool, select the generated and opened the port, the green light at this time should is still flashing status!!
Input the AT command in the string input box after sending.All the AT command must be capitalized!Each of the AT commands interval of AT least 1 second!!!!!
Testing communication instructions: send the AT, OK if module a reply indicates the hardware connection is no problem, you can send other commands to modify parameters
*회로설계,주문제작,개발용 부품 및 모듈 전문점
유틸전자주식회사
서울 용산구 한강로 3가 16-9 전자랜드 본관 광장층 C31호
02-706-7700 aproga@korea.com www.UTIL.co.kr |
|
|
|
|
|
유틸전자주식회사 | 서울시 용산구 청파로74 전자랜드본관 광장층 C-31호 | E-mail: aprogara@naver.com| 사업자번호: 106-86-72446
Tel:050-5500-4900 Hosting Server www.nexgeo.co.kr|개인정보책임자:김영현 | 통신판매업 용산00261호 
 |
|
|
|
|
|
|
|
|
